Home / All / Welding Equipment / All products /

3-in-1 Multi-process: dc tig+plasma cutting STC-205Di

3-in-1 Multi-process: dc tig+plasma cutting STC-205Di
3-in-1 Multi-process: dc tig+plasma cutting STC-205Di3-in-1 Multi-process: dc tig+plasma cutting STC-205Di3-in-1 Multi-process: dc tig+plasma cutting STC-205Di

3-in-1 Multi-process: dc tig+plasma cutting STC-205Di

3-in-1 Multi-process: dc tig+plasma cutting STC-205Di
CategoriesAll products
BrandTOPWELL
ModelSTC-205Di
Rated Input Voltage1PH ~ 230V ±15%
Rated Output200A/18V
Max Open Circuit Voltage5.63KVA
Effiency80%
Warranty1 year warranty
Dimensions:410*190*305mm
Weight15KG
Unit PriceUS $ 2 / piece
FOB portNingbo/Shanghai
Terms of PaymentL/C, D/A, D/P, Western Union, MoneyGram, T/T, Paypal
Download
Update TimeNov 24,2024
Detail Information
  • /FEATURES

    Quick Specs
    Light Industrial Application:
    Installation and set-up
    Repair and maintenance
    Thin sheet metal fabrication workshops
    Chemical and process industry
    Processes:
    DC TIG (GTAW)
    Plasma Cutting
    Stick (SMAW)
    Input Power: 230V, 1-Phase
    Amperage Range:TIG:TIG: 5A-200A/
    PAC: 20A-50A/MMA: 10A-160A
    Rated Output at 40℃ (104℉):
    TIG: 200A at 18V @60% Duty Cycle
    PAC: 50A at 105V @60% Duty Cycle
    MMA: 160A at 26.4V @60% Duty Cycle
    Weight: 15Kg

    General View of Control Panel

    STC-205Di-▏Multi-Process-Welders_03

    1.Remote:used for foot pedal or Remote torch.
      Local:adjusted Currents by face panel.
    2.2T/4T holding mode
      Spot Welding mode selection
    3.Pulse ON/OFF selection.

    4.Process selection.
    5.ARC FORCE
      HOT START
    6.Memory with capacity of 10 sets parameters.
    7.Function sequence


    General View of Control Panel(Continued)

    MASTER-TIG-350CT-400CT-500CT-▏TIG-Welders_0_07

    1.Gas pre-flow time(TIG)
       Absolute setting range 0.1s to 5.0s (0.1s increments).
    2.Ignition current(TIG)
       Percentage of the main current.
       4T(HOLD)
       Setting range 1% to 100%(1% increments).
    3.Up-slope time(TIG)
       Setting ranges:0.00s to 20.0s(0.1s increments).
       The up-slope time can be set separately
       for non-latched and latched.
    4.Main current(TIG)/pulse cuttent
      I min to max(1 A increments)
      Main cuttent(MMA)
      I min to I max(1 A increments)
    5.Pulse time
       Pulse time setting range:0.01s to 9.99s(0.01s increments)
       TIG pulses
       The pulse time applies to
       the main cuttent phase(AMP) for pulses.
       TIG AC Special
       The pulse time applies to the AC phase for AC special.

    6.Pulse break time
       Pulse break setting range:0.01s to 9.99s
       (0.01s increments).
       TIG pulses
       The pulse break time applies to the secondary
       current phase(AMP%).
       TIG AC Special
       The pulse time applies to the AC phase for AC special.
    7.Secondary current(TIG)/pulse pulse pause current
       Setting range 1% to 100% (1% increments).
       Percentage of the main current.
    8.Down-slope time(TIG)
      0.00s to 20.0s (0.1s increments).
      The down-slope time can be set separately
       for non-latched and latched.
    9.End-crater current(TIG)
       Setting range 1% to 100%(1% increments).
       Percentage of the main current.
    10.Gas post-flow time(TIG)
       Setting ranges:0.1s to 20.0s(0.1s increments).



    DC TIG-Pulse

    High Speed DC TIG-Pulse Controls
    • PPS Pulses per second (Hz):DC = 0.1 – 5,000 PPS
    • % ON – % Peak Time:5 - 95% (Controls the amount of time during each pulse cycle at the PEAK amperage.)
    • Background Amps:5 – 99% (Sets the low-pulse amperage value as a % of the Peak Amps.)

    CONVENTIONAL PULSED TIG

    HIGH SPEED PULSED TIG

    Typically from 1 to 10 PPS. Provides a heating and
    cooling effecton the weld puddle and can reduce
    distortion by lowering the average amperage. This
    heating and cooling effect also produces adistinct
    ripple pattern in the weld bead. The relationship
    between pulse frequency and travel speed determines
    the distance between the ripples. Slow pulsing can
    also be coordinated with filler metal addition and
    can increase overall control of the weld puddle.

    MASTER-TIG-350CT-400CT-500CT-▏TIG-Welders_0_35

    In excess of 40 PPS, Pulsed TIG becomes more
    audible than visible—causing increased puddle
    agitation for a better as-welded microstructure.

    Pulsing the weld current at high speeds — between
    a high Peak and a low Background amperage —
    can also constrict and focus the arc.This results in
    maximum arc stability, increased penetration and
    increased travel speeds(Common Range:100–500

    PPS).The Arc-Sharpening effects of high speed
    pulsing are expanded to new dimensions. The ability      
    to pulse at 5,000 PPS further enhances arc stability
    and concentration potential — which is are required.







    CUT PERFORMANCE

    CUT-40Di-40MV-▏Plasma-Cutters_06 CUT-40Di-40MV-▏Plasma-Cutters_08  
    Big cutting power in a small package - the
    industry's most portable and powerful
    40-amp plasma cutter offers 10mm.
    mild steel cutting. The unit offers easy
    connection to 115V or 230V input with
    Auto-Line technology and MVP Adapters.
     
    Rated Cut @ Maximum Cut @ Sever Cut @
    0.50 m/min 0.25 m/min 0.12 m/min




  • /SPECIFICATIONS


    Technical specifications

    Item NoSTC-205Di
    Rated Input Voltage1PH ~ 230V ±15%
    Max. Load Power CapacityTIG: 5.63KVA
     MMA: 6.60KVA
     PAC: 8.20KVA
    Rated Duty Cycle(40℃) 60%TIG: 200A/18V
     MMA: 160A/26.4V
     PAC: 50A/105V
                                          100%TIG: 160A/16.4V
     MMA: 130A/25.2V
     PAC: 40A/100V
    Welding Current/Voltage RangeTIG: 5A/10.2V~200A/18V
     MMA: 10A/20.4V~160A/26.4V
     PAC: 20A/90A~50A/105V
    Open Circuit VoltageTIG/MMA:70V~80V
     PAC:260V~290V
    Power Factor0.73
    Efficiency80%
    TIGPulse Frequency0.2Hz~200Hz
    Pulse Width (Ratio)1~100%
    Arc-starting Current5A~200A
    Crater-filling Current5A~200A
    Current Up-slope Time0.1S~15S
    Current Down-slop Time0.1S~15S
    Pre-Gas Time0.1S~15S
    Flow-Gas Time0.1S~15S
    Spot Arc Time0.1S~10S
    MMAArc Force10A~160A
    Hot Start Time10A~160A
    Hot Start Current0.1~3S
    PACRequired Air Pressure0.3~0.5MPa
    Gas Pro-flow/Retard Time0.1S~15S
    Quality Cutting Thickness(500mm/min)12mm
    Severance Cutting Thickness(125mm/min)22mm
    Dimension (LxWxH)410X190X305mm
    Weight (KG)15KG

  • /ACCESSORIES

    For Standard accessories
    4
    TIG torch:WP-26
    2
    Electrode holder with cable 2M
    HT-50CB
    Plasma torch: HT-50CB
    For Optional accessories
    01
    Argon gas regular
    03
    Foot Pedal
    02
    Hand-hold Remote Controller
    03
    Plasma torch: PT-60
    WT-100
    Trolley: TW-100
    02
    Water-cooling unit: WC-100
    TIG-26
    TIG torch: TIG-26
  • /RESOURCES

  • /DOCUMENTS

DC pulse TIG & plasma cutting machine

ac dc tig mma plasma cutting

dc tig+plasma cutting

3-in-1 Multi-process

welding machines

ANY COMMENTS? YOU ARE WELCOME TO LEAVE MESSAGE TO US!
*Email
Tel
*Title
*Content
Upload
  • Only supports .rar/.zip/.jpg/.png/.gif/.doc/.xls/.pdf, maximum 20MB.
Review
  • Loading...