Industrial DC Pulse TIG welding machine PROTIG-400CT with heavy duty power
Industrial DC Pulse TIG welding machine PROTIG-400CT with heavy duty power
/FEATURES
Quick Specs
- Application:
- Installation and set-up
- Repair and maintenance
- Metal fabrication workshops
- Chemical and process industry
- Processes:
- DC TIG (GTAW)
- Stick (SMAW)
- Input Power:
- 400CT/500CT: 400V, 3-Phase
- Amperage Range:
- 400CT:3-400A/ 500CT:3-500A
- Rated Output at 40℃ (104℉):
- 400CT: 400A at 26V @60% Duty Cycle
- 500CT: 500A at 30V @60% Duty Cycle
- Weight:70kg
General View of Control Panel
1.Remote:used for foot pedal or Remote torch.
Local:adjusted Currents by face panel.
2.2T/4T holding mode
Spot Welding mode selection
3.Pulse ON/OFF selection.4.Process selection.
5.ARC FORCE
HOT START
6.Memory with capacity of 10 sets parameters.
7.Function sequence
General View of Control Panel(Continued)
1.Gas pre-flow time(TIG)
Absolute setting range 0.1s to 5.0s (0.1s increments).
2.Ignition current(TIG)
Percentage of the main current.
4T(HOLD)
Setting range 1% to 100%(1% increments).
3.Up-slope time(TIG)
Setting ranges:0.00s to 20.0s(0.1s increments).
The up-slope time can be set separately
for non-latched and latched.
4.Main current(TIG)/pulse cuttent
I min to max(1 A increments)
Main cuttent(MMA)
I min to I max(1 A increments)
5.Pulse time
Pulse time setting range:0.01s to 9.99s(0.01s increments)
TIG pulses
The pulse time applies to
the main cuttent phase(AMP) for pulses.
TIG AC Special
The pulse time applies to the AC phase for AC special.6.Pulse break time
Pulse break setting range:0.01s to 9.99s
(0.01s increments).
TIG pulses
The pulse break time applies to the secondary
current phase(AMP%).
TIG AC Special
The pulse time applies to the AC phase for AC special.
7.Secondary current(TIG)/pulse pulse pause current
Setting range 1% to 100% (1% increments).
Percentage of the main current.
8.Down-slope time(TIG)
0.00s to 20.0s (0.1s increments).
The down-slope time can be set separately
for non-latched and latched.
9.End-crater current(TIG)
Setting range 1% to 100%(1% increments).
Percentage of the main current.
10.Gas post-flow time(TIG)
Setting ranges:0.1s to 20.0s(0.1s increments).
DC TIG-Pulse
High Speed DC TIG-Pulse Controls
• PPS Pulses per second (Hz):DC = 0.1 – 5,000 PPS
• % ON – % Peak Time:5 - 95% (Controls the amount of time during each pulse cycle at the PEAK amperage.)
• Background Amps:5 – 99% (Sets the low-pulse amperage value as a % of the Peak Amps.)CONVENTIONAL PULSED TIG
HIGH SPEED PULSED TIG
Typically from 1 to 10 PPS. Provides a heating and
cooling effecton the weld puddle and can reduce
distortion by lowering the average amperage. This
heating and cooling effect also produces adistinct
ripple pattern in the weld bead. The relationship
between pulse frequency and travel speed determines
the distance between the ripples. Slow pulsing can
also be coordinated with filler metal addition and
can increase overall control of the weld puddle.
In excess of 40 PPS, Pulsed TIG becomes more
audible than visible—causing increased puddle
agitation for a better as-welded microstructure.Pulsing the weld current at high speeds — between
a high Peak and a low Background amperage —
can also constrict and focus the arc.This results in
maximum arc stability, increased penetration and
increased travel speeds(Common Range:100–500PPS).The Arc-Sharpening effects of high speed
pulsing are expanded to new dimensions. The ability
to pulse at 5,000 PPS further enhances arc stability
and concentration potential — which is are required.
Hot Start
Hot start function reliably ignites the electrode and melts
perfectly to ensure the best quality even at the start of
the seam. This solution makes lack of fusion and cold weldsa thing of the past and significantly reduces weld reinforcement.
Adjust the hot start current here and the time here.
Arcforce correction (welding characteristics)
During the welding process, arcforce prevents the electrode sticking in the weld pool with increases in current.
This makes it easier to weld large-drop melting electrode types at low current strengths with a short arc in particular.
2T/4T
Non-latched mode
1st cycle:
• Press and hold torch trigger 1.
• The gas pre-flow time elapses.
• HF ignition pulses jump from the electrode to the workpiece,the arc ignites.
• The welding current flows and immediately assumes the value set for the ignition current Istart.
• HF is switched off.
• The welding current increases in the set up-slope time to the main current AMP.
Switching from main current AMP to secondary current AMP%:
Press torch trigger 2 or Tap torch trigger 1
2nd cycle:
• Release torch trigger 1.
• The main current decreases in the set down-slope time to the end-crater current Iend (minimum current).
If torch trigger 1 is pressed during the down-slope time,
the welding current increases again to the set main current AMP.
• The main current reaches the end-crater current Iend, the arc extinguishes.
• The set gas post-flow time elapses.Latched mode
Step 1
• Press torch trigger 1, the gas pre-flow time elapses.
• HF ignition pulses jump from the electrode to the workpiece, the arc ignites.
• Welding current flows and immediately assumes the ignition current value set
(search arc at minimum setting). HF is switched off.
Step 2
• Release torch trigger 1.
• The welding current increases with the set up-slope time to the main current AMP.
Switching from main current AMP to secondary current AMP%:
Press torch trigger 2 or Tap torch trigger 1
Step 3
• Press torch trigger 1.
• The main current decreases in the set down-slope time to the end-crater current Iend (minimum current).
Step 4
• Release torch trigger 1, the arc extinguishes.
• The set gas post-flow time begins.
Immediate termination of the welding process in the downslope by releasing torch trigger 1./SPECIFICATIONS
Technical specifications
Item No
PROTIG-400CT
PROTIG-500CTRated Input Voltage 3PH ~ 400V ±15% 3PH ~ 400V ±15% Max. Load Power Capacity TIG: 14.39 KVA TIG: 20.76 KVA MMA: 14.21 KVA MMA: 19.93 KVA Rated Duty Cycle(40℃) 60% TIG: 400A/26V TIG: 500A/30V MMA: 315A/32.6V MMA: 400A/36V 100% TIG: 315A/22.6V TIG: 400A/36V MMA: 250A/30V MMA: 315A/32.6V Welding Current/Voltage Range TIG:5A/10.1V~400A/26V TIG:20A/10.1V~500A/30V MMA: 20A/20.8V~315A/32.6V MMA: 20A/20.8V~400A/36V Open Circuit Voltage 70V~80V 70V ~80V Power Factor 0.85 0.85 Efficiency 85% 85% TIG Pulse Frequency 0.2Hz~200Hz 0.2Hz~200Hz Pulse Width (Ratio) 1~100% 1~100% Arc-starting Current 5A~400A 5A~160A Crater-filling Current 5A~400A 5A~500A Current Up-slope Time 0.1S~15S 0.1S~15S Current Down-slop Time 0.1S-15S 0.1S-15S Pre-Gas Time 0.1S-15S 0.1S-15S Flow-Gas Time 0.1S-15S 0.1S-15S Spot Arc Time 0.1S-10S 0.1S-10S MMA Arc Force 10A~315A 10A~400A Hot Start Time 0.1-3S 0.1-3S Hot Start Current 10A~315A 10A~400A Dimension (LxWxH) 960X420X900mm 960X420X900mm Weight (KG) 70 KG 70 KG Water-cooling Unit: WC-100
Operating Voltage 230V 50/60Hz Rated Power 260W Cooling Power 1.5KW(1L/MIN) Maximum Pressure 0.3MPA/60HZ Recommended Cooling Liquid 20%~40% ethanol/water Tank Volume 6.5L
/ACCESSORIES
For Standard accessories
TIG torch:TIG-18
Electrode holder with cable 2M
Water-cooling unit: WC-150For Optional accessories
Argon gas regular
Foot PedalTIG torch: TIG-26
Trolley:WT-150
Hand-hold Remote TIG torch/RESOURCES
/DOCUMENTS
- Tel
- *Title
- *Content
- Loading...